These vintage bicycles, frames, and parts are available for restoration purposes. Please Contact the site for details.
WTB Classic Grease Guard Hubs
New old stock WTB Grease Guard hubs for freewheel cogsets are available with the following options:
- Color: Silver or Black
- Hole Count: 28, 32, 36, 40, 48
- Front Axle: 100 mm
- Rear Axle: 120, 126, 130, 135, 140 mm
- 5, 6, 7, or 8 speed.
WTB Hub Cap Removal Tool
Special tool made by WTB to service their GreaseGuard hubs without damage.
WTB Grease Guard Hub Bearings
New old stock angle-contact bearings made especially for WTB with the inner seal removed for the grease purge. Theses are 9R-8T bearings by NBN of Japan. OD: 1.125", ID: 0.500", W: 0.313"
Enduro 6003 Bottom Bracket Bearing
New old stock 6003 Enduro bearings for press fit spindle OD: 35 mm, ID: 17 mm, W:10 mm
Paragon Machine Works Cable Hangers
New old stock headset cable hangers by Paragon Machine Works are a good substitute for WTB cable hangers. Available with a hard anodized finish, these come in both a 1" and 1-1/8" headset size.
Mafac Headset Cable Hangers
New old stock Mafac headset cable hangers available in stainless steel and zinc plating for D-shaped or keyed steerer.
T. A. Specialties Crank Bolts
New old stock TA Specialties bolts with washers. 15 mm hex head available as pairs.
Campagnolo Bottom Bracket Spindle
New old stock or very lightly used Record or Nuovo Record spindles marked 68-SS-120.
Magura Hexagon Rubber Grips
New old stock hexagonal Magura motorcycle grips, available with the flange removed (as shown) like the classic WTB product. Only three pairs left!
WTB Gripmaster Brake Pads
New old stock WTB Gripmaster pads with original Kool-Stop black compound and silver anodized aluminum holders
WTB Brake Bridge Booster
New old stock WTB brake bridge boosters for rollercam brakes measure 65 mm inside width, 104 mm outside width, and 40 mm tall opening. Each is ready to be drilled and includes the WTB stamped logo at the top.
Speedmaster Brake Springs
New old stock WTB stainless steel spring wires for WTB rollercam and cantilever brakes. Springs for older WTB brakes are also available.
WTB Speedmaster Brake Cams
New old stock WTB Rollercam cams are available for the newer DKG-made brake arms without lightening holes. Comes with cable mounting hardware and option of narrow, standard, or wide width. Also available in black.
WTB Speedmaster Brake Cams
New old stock WTB Rollercam cams are available for the early brake arms with lightening holes. Comes with cable mounting hardware and one standard width.
WTB Speedmaster Cantilever Cable
New old stock WTB straddle cable, hanger, and end hook for WTB Speedmaster cantilever brakes.
T. A. Specialties Crankset covers
New old stock covers with 5 mm hex holes for T. A. Specialties Cyclo-Tourist cranks.
T. A. Specialties Pedal Washers
New old stock T. A. Specialties thin washers protect crank arms from marring.
SRP Derailleur Pulley Bolts
Vintage SRP aluminum pulley hardware for:
- Shimano Deore XT M732
- Shimano Deore XT M735
- Shimano Deore XTR M900
- Shimano Deore XTR M910
- Shimano Dura Ace 7400
Color Options: Red, Blue, Black, Silver, Gold, Green, Violet.
Price: $6/pair plus shipping
This one of a kind bike features Ritchey Logic tubing and a premium mix of parts to go along with a custom paint job. With the AccuTrax fork, this custom bike is a phenomenal ride.
Full Photo Gallery: 1991 Ludichris
1994 Clark Kent 650c Road
This custom Clark-Kent titanium road bike was made with 650c wheels for a smaller rider. Built up with size appropriate bars and stem, this bike measures 45 cm center-to-center on the seattube with a 50 cm toptube. The bike is built with a collection of age appropriate Shimano parts.
Full Photo Gallery: 1994 Clark-Kent Road
1994 Clark-Kent F-16 FS (frame kit)
Titanium full-suspension frame with titanium Clark-Kent seatpost and stem. Also included is the Clark-Kent XLR9 crankset, which has cracks on the spindle ends. Rear shock holds air.
Seattube: 19" center to center
Toptube: 23.5" horizontal
Full Photo Gallery: 1994 Clark-Kent
WTB Toe Flips
New old stock WTB Toe Flip with stainless steel hardware. Some of the zinc plating may be inconsistent.
WTB Handlebar Shim
New old stock WTB shim for 7/8" handlebar and 1" stem clamp. Shims are 2.125" long. Please note these are not the long taper version that came with WTB titanium bars, but they will work for that purpose.
WTB Taper Stem Mounting Collet
New old stock WTB expansion collet for mounting of WTB stems to a cone brazed into the top of the fork steerer. The OD is available in various sizes.